The temperature activated control works effectively in re-circulating systems and in combination with tank-type heaters. High Efficiency Compact Design -Commercial models provide unlimited hot water while operating within their designed gallons per minute range, immediately heating water when a hot water outlet is opened. Seisco models install inside closets, or on almost any wall. Water is only heated on demand, virtually eliminating standby heat loss and providing over 99% efficiency. Microprocessor Control -On-board computer logic controls temperature through a modified proportional, integral, derivative [PID] control scheme.
The control also provides self-diagnostics, signal the need for maintenance in case of a water leak inside the heater, incorporates an optional switch for local on/off power interuption, and intelligently controls power distribution to the heating elements while continuously monitoring critical functions in order to shut down the water heater if a failure occurs. PowerShare Technology -Patented power distribution control technology utilizes computer algorithms and electronic triacs with patented cooling technology to pulse power on and off to all heating elements resulting in uniform temperature modulation between 1-100% of the element's range. PowerShare along with constantly flowing water across heating elements ensure that heating elements operate at the lowest possible temperature. When the elements are turned off, low sheath temperature prevents boiling minerals out of the water causing buildup on the heating elements, prolonging element life. PowerShare also eliminates electrical disturbances in the home from the water heater, such as flickering lights.Thermistor Temperature Sensing -Five thermistors continuously monitor inlet/outlet water temperature and the water temperature in each heating element chamber. Outlet water temperature is factory set to 120F and is field adjustable between 90-145F.
In addition, water flow is sensed using the same thermistors, eliminating the need for troublesome flow switches. Heating Elements -Industry standard 1 hex head, direct immersion, heating elements utilize PowerShare technology to help eliminate scale build-up and prolong element life far beyond that of tank type water heaters. Redundant Safety Features -Two water level sensors are located at the top of the water heater's chambers to prevent powering on the heating elements if sufficient water is not detected inside the water heater. In addition, two safety cutoff switches, one manual and one automatic reset, shut down power to the heating elements should an unsafe condition occur. Built-in Leak Detector and Alarm -A switch located inside the water heater's cover along the bottom of the mounting plate activates an alarm when contacted by water.The service agent can also diagnose a problem through observing an LED that indicates service issues through a series of flashes. Rust and Corrosion Resistant Engineering Composite Material - All water passages are constructed of a high temperature resistant DuPont resin. Grades of the same resin family, but with lower properties, are so strong that they are used as the header for automobile radiators. Ability to resist extreme temperature changes far above those found inside Seisco models and superior chemical resistance make DuPont's engineering composite material the ideal material for Seisco's commercial tankless electric water heaters. Continuous Venting Design -As water is heated, dissolved gases are released.
Tiny bypass air passages at the top of each water chamber allow air and dissolved gases to exit unnoticed through the hot water outlet as hot water is being used. Optional Demand Side Management Connection - Allows connection of an on/off control to the water heater [specify this option when ordering]. Cleanout Plates -Should sediment such as sand or silt from the water supply accumulate inside the water chambers, removable plates sealed with reusable gaskets allow access for cleaning without disconnecting wires or removing the heating module and control board. Non-Ferrous Inlet/Outlet Connections -Factory installed MNPT thermoplastic nipples allow easy plumbing connections and eliminate the need for dielectric fittings Heavy Gauge Steel Mounting Panel -Modular water passages, the control board, and other components are assembled and then mounted to a heavy gauge steel back panel that includes four tabs with rubber feet for mounting the unit to the wall. A decorative plastic cover encloses all components. Electrical Conduit Connection -Standard electrical conduit connections allow fast wiring of the water heater. Code Approvals -UL/CUL 499/64, HUD Mobile Home, ISRAEL, NOM, and NEC.Hydrostatically tested to 300 psi. The item "Seisco Tankless Electric Water Heater CA-11 (240V) 2 Chamber for commercial use" is in sale since Sunday, December 15, 2019. This item is in the category "Home & Garden\Home Improvement\Heating, Cooling & Air\Water Heaters\Tankless Water Heaters". The seller is "som533" and is located in Irving, Texas. This item can be shipped to United States, Canada, United Kingdom, China, Mexico, Germany, Japan, Brazil, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.